this is just a test - Page 012

ARC don't show number of chips but it works for test. I see all my signals CLOCK RX RST LDOS.

how to dump the eeprom information, the log file not show the hex information.

S19 J Pro. Hashboard BHB42631

I think we're having the same problem.

I use this dump file to flash on our hashboard and it work.

but still got "0 chip found"

BM1362AK

I cannot dump the board. It show empty

In the miner log file also no information.

Check it please

Hi. I have this error on 2 t17 hb

The boards seems ok on tester ... any help?

Error_temperature_too_high

Note: the power supply VDD IN = 17.6 V ... the voltage in hashboard test is less in screen

Put your voltage at 21v, amp to max, while doing your tests

Then, if you got red at Advanced test (little thunder), you could check BI signal, it's supposed to be at 0

while advanced test on, check all the chips from last to first. If you got a chip that has a Bi of 1.8, usually it's that one that is causing the problem

But yeah, red advanced test on T17 is not an easy one

In 3rd domain voltage is equal to 2.3v, when normally is 1.5 to 1.9v in the other domains

Pls help i want dump file of this version s19j pro 104t

2022-09-15 16:07:53 temperature.c:697:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 184, reg = 1
2022-09-15 16:07:54 thread.c:734:check_temperature: over max temp, pcb temp 61 (max 80), chip temp 191(max 103)
2022-09-15 16:07:54 driver-btm-api.c:205:set_miner_status: ERROR_TEMP_TOO_HIGH

-

Like that with a shorting probe 😓

what means chip=184?

2022-09-15 19:19:08 thread.c:734:check_temperature: over max temp, pcb temp 50 (max 80), chip temp 104(max 103)
2022-09-15 19:19:08 driver-btm-api.c:205:set_miner_status: ERROR_TEMP_TOO_HIGH
2022-09-15 19:19:08 driver-btm-api.c:146:stop_mining: stop mining: over max temp
2022-09-15 19:19:08 thread.c:920:cancel_temperature_monitor_thread: cancel thread
2022-09-15 19:19:08 thread.c:930:cancel_read_nonce_reg_thread: cancel thread
2022-09-15 19:19:08 driver-btm-api.c:131:killall_hashboard: ****power off hashboard****

its drive me crazy :)

seems like asic, but on tester all sensors are detected and are ok

Sorry if I was stating the obvious but I hope it helps....

The 4-sensor temp is Ok... (pcb-trmp)
Your problem is some Asic...

What to understand from this? In normal mode all ok, but in advance mode 1 asic?! Tnx!

Here i just saw 2631

I will try others 3 options

Number 2 working thanks guys

Now show 124 of 126 chips i will open to try repair

You got Voltage going down and Current going up?

Look if boost circuit got juice

Look RI signal from last chip to first
Check CLK

the voltage does not drain when not testing. I will try injecting voltage before and after those components to try to find the issue. Thanks Austin

It worked fine for a week i was fixing many miners then it just randomly logged out. My wifi connection is good . Was able to go to reset the connection once and now it just flash start system and if hold ted button it just does failed to connect... Configuring access point

I changed the eeprom memory and the problem was solved ..thanks ..

I need support how to updat ARC Asic tester .L7 Model not in my Tester

Also while updating showing error

N10001214

ead time

whats is mean

hi! very strange, share the dump, we will study it. does the board work fine in the miner?

What is the use of the lighting and R ?

An advanced mode is a mode in which an address is distributed to each chip and the polling takes place automatically. In normal mode, the survey is broadcast.

Hello

Temperature sensor flashing red/ green

What that supposed to mean?

out of range

something line -10 or 120 ...

like